How to Recondition Wiper Blades | A Step by Step Guide

How to Recondition Wiper Blades

Wiper blades are rubber blades used to wipe water from the windshield of cars. Wiper blades are perhaps one of the most neglected car parts. Most car owners do not give this part the attention it requires. They do not change it when it strains, and they do not clean it. It leads to the deterioration of the car’s windshield, which can be a problem. Instead, it will talk about how you can clean and recondition your wiper blades.

How to Recondition Wiper Blades

How to Recondition Wiper Blades

Here are steps you can take to recondition your wiper blades:

  • Wipe off any mold or residue from the old wiper blades.
  • Scrape off any rust. If you don’t have sandpaper, you can use a scouring pad. It gets the job done!
  • Pour a quarter beaker of baking soda into a plastic bag, and wrap your wiper blades. You can put newspaper or a plastic bag on your car but make sure the edges don’t touch anything!
  • Tie the bag off with string. It will make these super fresh and clean!
  • Put the blades back on your car.
  • Take the wiper blades off, pour a quarter cup of vinegar in the bag, and tie it off.
  • The vinegar will make your wiper blades softer and more pliable, which will give you a better wipe!

More Techniques to Recondition Your Wiper Blades

More Techniques to Recondition Your Wiper Blades

Straightening Tool

There are many ways to recondition wiper blades, but the most popular way is to use a straightening tool. A straightening tool is a tool used for cars. It essentially straightens bent metal. To use this tool on your wiper blades, you need to hold the wiper blade from the bottom and spread it apart with the device.

The edge should straighten out to its former glory. Then, dry it off with a cotton towel and re-install it inside your vehicle. The blade should work as if it were brand new!

Wiper Fluid

The wiper blades are very vital parts of our vehicles. It will be difficult to drive correctly in bad weather without them. Thus, we must recondition the blades. Here are some tips to help: First, never spray any liquid directly on the edges.

It can cause corrosion and will destroy the wipers. Be sure to use the wiper fluid properly. The juice should only apply to the windshield. We should utilize the liquid. And clean the blades regularly. We can also consider replacing the blades regularly.

Compressed Air

Wiper blades can become a little worn over time. The rubber may get tricky, and it may even start to squeak when you turn your wipers on. But it’s not sufficient to return the real dagger!

If this happens to you, you can use a simple best practice trick for reconditioning your wipers so that you don’t have to go to a mechanic to get new ones! 

Here’s how you do it. First, attaches the wiper blades to your windshield as usual. Then take some compressed air, hold it about 6 inches away from the rubber, and spray the compressed air for about 10 seconds. After you do that, wipe down the rubber with a dry cleaning cloth, and it’ll return to a silky smooth coating, and it’ll be like new!

Silicone Lubricant:

You are rubbing a silicone lubricant into a wiper blade once every three months can keep them in good condition. You rub it on and then let it sit for 15 minutes. Usually, the silicone lubricant will dry, and you’ll be able to wipe the excess away.

You’ll be surprised how smooth your wipers can be. It is better than putting oil on them because silicone doesn’t evaporate, so it doesn’t leave a residue on your windshield.

Vinegar and Water

You can recondition your wiper blades with vinegar and water if they look faded, chipped, or cracked. First, remove the wiper blade from the arm and submerge it in a bowl of vinegar and water for 15 minutes. Remove the edge from the bowl, brush it off, and put it back on the arm.

Your blades should be looking brand new! If you don’t want to use the vinegar method, you can also use a buffer with steel wool. It will also help you clean off any extra dirt or grime.

Frequently Asked Questions

How to Recondition Horizontal Arm Wiper Blades?

The best way to recondition horizontal arm wiper blades is to use a thin, plastic card, such as a credit card. The edges must leave to dry after the rain. Then it would help if you scraped away any dried-on dirt or debris from the blade with a small piece of sandpaper, then wiped it clean with a cloth or paper towel. 

Does WD-40 Restore Wiper Blades?

WD-40 DOES NOT RESTORE WIPER BLADES. WD-40 is a water displacer designed to eliminate water that does not belong on the surface it is sprayed onto, like on an engine. It also protects against rusting and corrosion. We recommend using silicone spray to restore wiper blades.

How Do You Soften Hard Windshield Wipers?

Acetone uses to soften hard windshield wipers. The wiper blades soak in an alcohol-acetone solution for about 10 minutes. After the rubber absorbs the acetone, it will loosen up and become pliable.

How Do You Restore Rubber Wiper Blades?

It is possible to restore rubber wiper blades to last an extended period. All you need to do is clean the rubber blade and dry it off to prevent overspray and rust. Once the rubber wiper blade has been cleaned and dried, coat the edge with silicone spray to make it more resilient and prevent rusting.

Conclusion

We hope you enjoyed our article on how to recondition wiper blades. When you think about it, wiper blades play a vital role in our lives. They help keep us safe by improving visibility on the road, but they also help us get to where we need to be. When our wipers are in bad shape, this can be problematic. Thanks to our blog, you now know how to recondition wiper blades.